A Ford oil change can cost anywhere from $30 to $140—this price is dependent on the model you drive, the type of oil it needs, and where you get the oil change performed.
Oil is an integral part of a healthy engine—without clean oil, your engine can overheat and break down. Oil gets dirty over time, which lessens its effectiveness. You’ll need to get regular oil changes to keep your engine happy.
How much does a Ford oil change cost?
A Ford oil change can cost anywhere from $30 to $140. The model, manufacturer year, and type of oil all impact how much you’re likely to pay.
Below is a comparison of the average oil change price for a trio of popular Ford models: the F-150, the Explorer, and the Expedition. The pricing estimates were sourced from Repair Pal and Kelley Blue Book.
| Model | Repairpal estimate | KBB estimate |
|---|---|---|
| F-150 | $125 to $139 | $93 to $126 |
| Explorer | $125 to $139 | $58 to $80 |
| Expedition | $121 to $133 | $60 to $82 |
Compare insurance quotes from 50+ carriers with Jerry in under 45 secondsZIP Code
4.7/5 App Store Rating. Trusted by 2+ Million Customers.
Here are a few explanations for the discrepancy in possible prices for a Ford oil change:
- Ford service center vs. local repair shop: Taking your car to a Ford-specific repair center will give you specialized service and expert knowledge. It will also likely cost you more than an oil change at a Jiffy Lube or local repair shop.
- Type of oil: Synthetic oil is specialized and made to last longer and provide top-tier engine performance. However, synthetic oil is significantly more expensive than conventional oil. Check your owner’s manual to see the oil recommendation for your Ford.
- Oil filter: There’s a high chance your oil filter needs replacement when you go in for an oil change. The cost of an oil filter can vary depending on the brand and quality of the filter.
Remember that the above costs factor in both the labor time and cost of parts. That means you’re paying for the literal oil and filter, plus the mechanic’s time to do the oil change.
Your zip code and market fluctuations can also cause the cost of your oil change to rise or fall.
Are oil changes more expensive for a Ford?
While it depends on the model you drive, Ford oil changes are likely similar to the average price across car models or slightly higher.
For cars that take conventional oil, you can still find an oil change for as low as $30, although this price may be tough to find for any newer Ford models.
However, Ford owners have long praised the brand’s toughness and longevity, so you can know your money is going toward a dependable vehicle.
Why is it important to change the oil in your Ford vehicle?
One of the most important things you can do to maintain your Ford vehicle is to keep up with regular oil changes. Changing your vehicle’s oil regularly helps ensure optimal performance, fuel efficiency, and longevity. It also keeps your engine clean and running smoothly.
Oil serves many purposes in an automotive engine. Its main purpose is to lubricate moving parts so they don’t grind against each other and cause wear or damage over time. Oil also helps cool the engine by carrying heat away from the combustion chamber; it acts as a sealant that prevents air and moisture from entering the internal components; and it helps collect dirt, debris, and contaminants that can build up over time if not removed from your motor on a regular basis.
Over time, motor oil breaks down due to normal use or environmental factors like extreme temperatures or pollutants in the air. This causes it to become less effective at its job of lubricating, cooling, sealing off air/moisture entry points, and removing contamination particles from within your engine’s components. Therefore changing out old oil for new will help make sure all these critical functions are being performed optimally inside your motor—helping prevent costly repair bills later on down the road!
Additionally, using synthetic oils instead of conventional oils can give you additional benefits when it comes to keeping up with proper maintenance schedules for your Ford vehicle since they tend to last longer than conventional oils before needing replacements (typically 5-7K miles). Synthetic blends offer even more protection against wear and tear since they contain higher levels of detergents that help keep engines clean while providing better lubrication properties than conventional oils alone can provide.
How often should you change the oil in a Ford car or truck?
It is important to keep your Ford car or truck running smoothly by regularly changing the oil. Depending on the type of vehicle and engine, it is recommended that drivers change the oil in their Ford cars or trucks every 3,000 to 10,000 miles.
For most vehicles manufactured after 2010, Ford recommends an oil change interval of 7500-10500 miles for conventional motor oil and 5000-7000 miles for synthetic blend oils. However, these intervals can vary depending on a variety of factors such as driving conditions and how much you use your vehicle.
To be sure when you should change your oil, it’s best to consult with your owner’s manual or take a look at the maintenance schedule included in your glove box. The manual will provide detailed information about what type of oil is appropriate for your model year along with specific instructions on how often to inspect and/or replace it. Additionally, if you have any questions about when you should have an oil change service performed for your particular make and model of Ford car or truck then don’t hesitate to contact a certified technician at any authorized dealership who will be able to give more personalized advice based on the condition of your engine and other factors like age and mileage.
What type of oil is recommended for Ford vehicles?
When it comes to proper maintenance of your Ford vehicle, choosing the right type of oil is essential. Depending on the model year and engine type, different types of motor oil are recommended for maximum performance and protection. Here’s what you need to know about selecting oil specifically designed for Ford vehicles:
Synthetic Oil Ford recommends using synthetic motor oil in all its vehicles built after 2011. Synthetic oils are manufactured through a process that creates a higher quality product than traditional mineral-based oils. This helps ensure optimal engine performance, improved fuel economy, lower emissions, and better overall wear protection. For ultimate performance in extreme temperatures (both hot and cold), look for an API SN Plus or ILSAC GF-6 certified synthetic motor oil when servicing your vehicle.
Conventional Mineral Oil For older Ford models not requiring synthetic oil (typically pre-2011), conventional mineral based motor oils should be used instead. These types of oils are derived from crude petroleum and must meet certain standards set by the American Petroleum Institute (API) before being approved for use in engines. Look for an API “Starburst” label indicating that it meets current industry specifications such as SN or SL ratings if you plan on using conventional mineral based motor oil in your vehicle’s engine.
Other Considerations In addition to choosing the correct type of motor oil, consider other factors such as viscosity ratings, additives included with some brands/types of oils, formulations designed specifically for diesel engines etc., when deciding which one is best suited to your particular Ford model(s). Viscosity ratings indicate how well an oil flows at various temperatures while additives can help improve lubrication properties or reduce deposits over time; both should be taken into consideration depending on where you live/drive most often and what specific needs you may have with regard to engine performance/protection requirements. Finally, remember that even though there may be slight variations between different manufacturers’ products – all should still meet minimum standards required by Ford Motor Company so don’t worry too much about brand selection!
How often should a Ford get an oil change?
For vehicles released after 2007, Ford recommends an oil change every 7,500 or six months, whichever comes first. For vehicles from 2007 or older, the recommendation is to change your oil every 5,000 miles or six months, whichever comes first.
Cars with synthetic oil can likely go longer between oil changes than conventional oil.
Check your owner’s manual to find your vehicle’s exact recommended oil change interval.
If you’re experiencing any of the following symptoms, it might be time for an oil change (even if it hasn’t been six months):
- A new engine sound.
- A burning smell.
- An illuminated dashboard light.
How to do a Ford oil change yourself: step by step instructions
Changing the oil in your Ford vehicle is an important part of routine maintenance that can help extend the life of your engine and keep it running efficiently. Fortunately, changing the oil yourself is a relatively simple process. With some basic supplies, you can do it yourself in just a few steps.
Changing the oil in your Ford vehicle is an important part of routine maintenance that can help extend the life of your engine and keep it running efficiently. Fortunately, changing the oil yourself is a relatively simple process. With some basic supplies, you can do it yourself in just a few steps.
Step 1
Preparing Your Vehicle Before beginning any work on your car, make sure that you have enough space to move around safely. Place wheel chocks behind the rear wheels if necessary so that the vehicle does not roll away while you are working on it. Turn off your engine and let it cool down before getting started; hot engines may leak fluids when being worked on. Locate the oil cap under the hood and open it up to release pressure from within the system before proceeding with a drain/fill procedure.
Step 2
Draining The Old Oil To start draining out old oil, locate where your cars’ oil pan is located beneath its engine block by referring to its service manual or online guide provided by Ford Motor Company.. Then place one end of a plastic drain pan underneath this area to catch all drained fluids, as well as any debris which may come out during this process. Unscrew both bolts at either side of this section using either a socket wrench or ratchet set until they are completely removed from their positions. Allow all spent oils remaining in system’s sump area to fully empty into said container before replacing them securely back onto their respective locations using same tools used earlier .
Step 3
Replacing The Oil Filter Now that most of old fluid has been drained out from car’s system, next step involves removing existing filter found near bottom portion of motor block adjacent towards transmission housing unit (again refer to manufacturer’s user guide regarding exact location). Loosen up any fasteners attached around circumference of such component using same tools mentioned earlier , then remove entire assembly once undone correctly . Wipe down surface area surrounding new filter housing site with clean rag beforehand in order remove dirt and other foreign items present prior installation . Begin installing new filter by firstly placing rubber gasket included with product onto base plate facing downwards towards opening inside motor block , then screwing unit tightly into position until secure . Make sure not over tighten components too much otherwise risk damaging threads inside cylinder wall itself which could lead further problems later down line .
Step 4
Refilling With New Oil Finally time refill system fresh supply lubricant! Start off pouring recommended amount stated manufacture’s handbook directly into dipstick tube via funnel ensure no spills occur during process – be careful here since overfilling may cause damage various internal components engine compartment depending model year vehicle own .. Once done adding liquid slowly begin replacing plug lid tight seal top avoid contamination outside environment ! After closing cap double check level dipstick against maximum fill line indicated user guide confirm everything ok proceed next step ..
Step 5
Finishing Up And Cleanup There should now be plenty fresh within car ready go however still few things left do complete job properly ! Firstly wipe down exterior areas affected recent procedure including dipstick valve cover grommet prevent rust buildup occurring future date secondly dispose used materials responsibly local waste centre afterwards ensuring no hazardous chemicals leaking into environment lastly re-check levels one final time ensure everything correct before starting driving again ..
Step 6
Congratulations! You’ve successfully changed the oil in your Ford yourself! If ever unsure about anything during this process always consult professional mechanic help answer any questions might have due complexity involved completing job correctly safety reasons good luck future endeavors!
Estimated Cost: 120 USD
Supply:
- • Oil – check your owner’s manual for the right type and amount to use
- • An oil filter – again, check your manual for specifics
- • Socket wrench or ratchet set
- • Funnel
- • Plastic drain pan (optional)
- • Towels and rags (for cleanup)
Where to go for professional Ford oil change services?
When it comes to professional oil change services for your Ford vehicle, you want to make sure you are going to a reputable shop that knows the ins and outs of your car. Fortunately, there are many options available when it comes to getting a professional Ford oil change service.
The most obvious choice is the dealership where you bought your vehicle. Most dealerships have certified technicians who specialize in Ford vehicles and can provide top-notch service for an oil change on any model of Ford. They also use genuine Ford parts and motor oils, so you know that your engine is getting the best care possible. The downside is that dealership prices can be more expensive than other places, so if cost is a factor this may not be the best option for you.
Another great option for getting a professional oil change service on your Ford is a local independent auto repair shop with ASE-certified technicians. These shops often offer competitive pricing compared to dealerships and still use high-quality parts and lubricants recommended by Ford Motor Company for their vehicles. Be sure to check reviews online before choosing an independent shop as some may not have experience working on Fords or even cars in general.
Finally, another great place to get a reliable oil change service done on your Ford vehicle is at one of the many national quick lube chains like Jiffy Lube or Valvoline Instant Oil Change (VIOC). These shops typically employ experienced mechanics who know how to properly perform an oil change on any type of car including Fords, plus they offer several different types of motor oils depending on what type your car requires and how often it needs changing (e.g., synthetic blend vs full synthetic). Plus, these stores have convenient hours making them ideal if time is tight or if you need same day service!
Common mistakes to avoid when changing the oil in your Ford vehicle
One of the most important tasks you can do on your Ford vehicle is to regularly change its oil. It’s an easy job, but there are some common mistakes that people make when changing their oil that could lead to serious damage or even voiding the warranty. Here are some of the most common mistakes to avoid when changing the oil in a Ford vehicle:
- Not Using The Proper Oil Type: Different vehicles have different requirements for which type of motor oil should be used. Make sure you use the correct type and weight of oil for your specific engine as recommended by the manufacturer. Using an incorrect type or weight of motor oil could cause serious harm to your engine and potentially void your warranty.
- Not Changing Oil Filters: Replacing just the motor oil without replacing its filter will only partially refresh your system, leaving behind dirt and grime that can eventually clog up parts and reduce efficiency over time. Be sure to always replace both elements during each service interval for optimal performance and protection against wear-and-tear damage.
- Overfilling The Engine Oil Reservoir: When filling up with new engine oil, it’s important not to exceed what’s recommended by the manufacturer as doing so can cause problems with certain components like turbochargers, PCV valves, etc., and may also trigger warning lights on dashboard displays due to high pressure readings from overly full reservoirs..
- Reusing Old Gaskets And O-Rings: Anytime you replace something containing rubber gaskets or O-rings (e.g., drain plugs), make sure you get a new set rather than reusing old ones since these materials tend to degrade over time due to exposure from heat/cold cycles, chemicals/solvents etc., leading them becoming brittle or cracking apart prematurely if reused too often for critical functions like sealing off fluid leaks around joints between two different parts..
- Failing To Tighten Parts Securely Enough: During assembly after draining out old fluids and refilling with fresh ones; be sure all bolts & screws are tightened firmly enough without overtightening (which can strip threads). Overtightening some types of fasteners can actually decrease their holding power while under tightening makes them prone to being shaken loose easily while driving – either way ending up creating more problems than it solves in terms of reliability & safety down road..
In short, when changing oils in a Ford vehicle – don’t forget about using proper oils & filters; avoiding overfill situations; replacing any worn out gaskets/o-rings; making sure everything is securely tightened before starting back up again – all these steps will help ensure smooth operation longer term without any unforeseen issues popping up along way!
Do I need synthetic oil in my Ford?
The use of synthetic oil in a Ford vehicle depends on the model and year of the car, as well as the manufacturer’s recommendations for oil type and viscosity. It is important to consult the owner’s manual or contact a Ford dealership to determine the appropriate type of oil for your specific vehicle.
In general, newer Ford vehicles are designed to accept synthetic oil, and in some cases, it may even be required to maintain the warranty. Synthetic oil has a number of benefits over conventional oil, including improved performance in extreme temperatures, longer oil life, and reduced engine wear.
However, it is also important to consider the cost of synthetic oil, as it is typically more expensive than conventional oil. Before making a decision, it may be a good idea to weigh the benefits and costs of synthetic oil and consider any personal driving habits, climate conditions, and vehicle usage patterns that may impact the decision.
How much is an oil change on a Ford?
The average cost of an oil change on a Ford vehicle ranges from $30 to $80 depending on the type of oil and location of the service.
How often should the oil be changed in a Ford?
The recommended oil change interval for a Ford can vary depending on the make and model of the vehicle, as well as the type of oil being used. However, in general, it is recommended to change the oil every 7,500 to 10,000 miles, or every 6 months, whichever comes first. It's important to refer to your owner's manual for specific recommendations for your Ford vehicle.
What does Ford oil change include?
The Ford Works® package typically includes a synthetic blend oil change, tire rotation and pressure check, brake inspection, multi-point inspection, fluid top-off, battery test, and filter, belts, and hoses check. The frequency of oil changes recommended for a Ford vehicle varies by model and year, but it is generally recommended to follow the manufacturer's guidelines for oil change intervals.
What is the labor cost of an oil change?
The labor cost of an oil change can vary depending on the location and the specific auto shop. On average, labor costs for an oil change are estimated to be between $20 and $50. However, this cost can be higher or lower depending on factors such as the type of oil used, the type of vehicle, and any additional services provided during the oil change.
How expensive is Ford maintenance?
The cost of Ford maintenance varies depending on the type of service needed, the age of the vehicle, and other factors. Routine maintenance tasks like oil changes, tire rotations, and brake inspections tend to be relatively affordable. However, more complex repairs or replacements can be expensive. It's a good idea to budget for regular maintenance and have an emergency fund in case unexpected repairs are needed.
How long can a Ford go without an oil change?
Ford recommends changing the oil every 7,500 to 10,000 miles or every 12 months, whichever comes first. Going longer than this recommended interval can cause engine damage and other costly problems, so it is important to stick to the recommended oil change schedule.
6 thoughts on “10 Step: How much does a Ford oil change cost?”